Universal uni-/bipolar signal transmitter
4104
- Measures and outputs uni-/bipolar voltage and current signals
- Works with both passive and active inputs and outputs
- Uses the PR 4500 display series for programming and process monitoring
- Fast < 20 ms response time and excellent < 0.05% accuracy
- Universally powered by 21.6…253 VAC / 19.2...300 VDC
Application
- Fast < 20 ms response time for measuring signals produced by torque, position, current & acceleration sensors.
- User configurable bipolar or unipolar I/O means the 4104 is suitable for nearly any voltage or current conversion.
- The excitation source enables measurement of two or three wire transmitters.
- The active or passive I/O makes the 4104 perfect for power matching current loops.
- Converts narrow bipolar inputs to wide bipolar or unipolar outputs, e.g., ±1 volt input = ±10 volt or 4...20 mA output.
- Selectable direct or inverse I/O makes the 4104 suitable for proportional control applications.
- The ”V-curve” function outputs 100% – 0 – 100% when a 0 – 100% input signal is present.
Technical characteristics
- The latest analog and digital techniques are used to obtain maximum accuracy and immunity to interference.
- The current output can drive up to 800 Ohms, with an adjustable response time of 0.0…60.0 seconds.
- Exceptional mA output load stability of < 0.001% of span/100 Ohm.
- Meets the NAMUR NE21 recommendations, ensuring high accuracy in harsh EMC environments.
- Meets the NAMUR NE43 recommendations, allowing the control system to easily detect a sensor error.
- Each unit is tested to a high 2.3 kVAC, 3-port galvanic isolation level.
- Excellent signal to noise ratio of > 60 dB.
Mounting / installation / programming
- Very low power consumption means units can be mounted side by side without an air gap – even at 60°C ambient temperature.
- Approved for marine applications.
- Configuration, monitoring, 2-point process calibration and more are accomplished using PR's 4500 series of detachable displays.
- All programming can be password protected.
Data sheet & Manuals
Data sheet
- 4104.pdf
- Latest version
Manuals
- 4104V103_UK.pdf
- 4104V102_UK.pdf
- 4104V101_UK.pdf
- 4104V100_UK.pdf
- Previous versions
- Latest version
Manuals in Russian
- 4104V103_RU.pdf
- 4104V102_RU.pdf
- 4104V101_RU.pdf
- Previous versions
- Latest version
Supplementary documentation
EU Declaration of Conformity
- 4104DoC_EU_103_UK.pdf
- 4104DoC_EU_102_UK.pdf
- 4104DoC_EU_101_UK.pdf
- 4104DoC_EU_100_UK.pdf
- Previous versions
- Latest version
UKCA Declaration of Conformity
- 4104DoC_UKCA_100_UK.pdf
- Latest version
Modbus configuration manual
- 4104_MCM_101.pdf
- 4104_MCM_100.pdf
- Previous versions
- Latest version
EMC data
- 4000_EMC_data.pdf
- Latest version
PR default configurations
- PR_default_configurations.pdf
- Latest version
Safety note
Safety note
- SN4000_1_107_2420.pdf
- SN4000_1_106_2109.pdf
- SN4000_105_2001.pdf
- SN4000_104_1741.pdf
- SN4000_103_1613.pdf
- SN4000_102_1506.pdf
- Previous versions
- Latest version
Approvals & Certificates
FM certificate
- 4104_14_16_31_4222_FM.pdf
- Latest version
UL certificate
- 4104_4179_4184_UL.pdf
- Latest version
DNV marine certificate
- DNV_2231_41xx_51xx_53xx.pdf
- Latest version
EAC declaration
- EAC-Declaration.pdf
- Latest version
Metrology Pattern Approval (MPA), Russia
- MPA_Russia.pdf
- Latest version
Order form
Environmental Conditions
Operating temperature | -20°C to +60°C |
Storage temperature | -20°C to +85°C |
Calibration temperature | 20...28°C |
Relative humidity | < 95% RH (non-cond.) |
Protection degree | IP20 |
Installation in | Pollution degree 2 & meas. / overvoltage cat. II |
Mechanical specifications
Dimensions (HxWxD) | 109 x 23.5 x 104 mm |
Weight approx. | 155 g |
Weight incl. 4501 / 451x (approx.) | 170 g / 185 g |
DIN rail type | DIN EN 60715/35 mm |
Wire size | 0.13...2.08 mm2 AWG 26...14 stranded wire |
Screw terminal torque | 0.5 Nm |
Vibration | IEC 60068-2-6 |
2...13.2 Hz | ±1 mm |
13.2...100 Hz | ±0.7 g |
Common specifications
Supply |
|
Supply voltage, universal | 21.6...253 VAC, 50...60 Hz or 19.2...300 VDC |
Max. required power | ≤ 2.5 W |
Max. power dissipation | ≤ 2.5 W |
Isolation voltage |
|
Isolation voltage, test / working | 2.3 kVAC / 250 VAC |
Response time |
|
Response time (0...90%, 100...10%) | < 20 ms |
Auxiliary supplies |
|
2-wire loop supply | > 16 V / 20 mA |
3-wire loop supply | > 18 V / 20 mA |
Loop supply limitation | 30 mA |
Programming | PR 4500 communication interfaces |
Signal / noise ratio | > 60 dB |
Cut-off frequency (3 dB) | > 40 Hz |
Accuracy | Better than 0.05% of selected range |
EMC immunity influence | < ±0.5% of span |
Extended EMC immunity: NAMUR NE21, A criterion, burst | < ±1% of span |
Input specifications
Current input |
|
Signal range | ±23 mA |
Programmable measurement ranges |
0...20 and 4...20 mA
± 10 and ± 20 mA |
Input voltage drop | 1.4 V @ 20 mA |
Loop error detection, 4...20 mA: Low | < 3.6 mA |
Loop error detection, 4...20 mA: High | > 21 mA |
Voltage input |
|
Signal range | ±12 V |
Programmable measurement ranges |
0/0.2...1, 0/1...5, 0/2...10 VDC
±1, ±5 and ±10 V |
Input resistance | > 2 MΩ |
Output specifications
Current output |
|
Signal range |
0...23 mA (unipolar)
-23...+23 mA (bipolar) |
Current limit |
≤ 28 mA (unipolar)
± 28 mA (bipolar) |
Load stability | ≤ 0.001% of span / 100 Ω |
Response time, programmable | 0.0...60.0 s |
Output limitation, on 4...20 and 20...4 mA signals | 3.8...20.5 mA |
Output limitation, on other unipolar mA signals | 0 and 115% of max. value |
Output limitation, on bipolar mA signals | ±115% of min. & max. values |
Sensor error indication, at 4...20 mA input: selectable | Low, High, Zero, None |
Active unipolar and bipolar mA output |
|
Programmable ranges |
0...20 and 4...20 mA
±10 and ±20 mA Direct or Inverted Action |
V-curve function, active signals, 100-0-100% | 20-0-20 mA |
Load (@ current output) | ≤ 800 Ω |
Passive 2-wire mA output |
|
Programmable ranges |
0...20 and 4...20 mA
Direct or Inverted action |
V-curve function, 100-0-100% | 20-0-20 mA |
External loop supply | 3.5 - 26 V |
Voltage output |
|
Programmable signal ranges |
0/0.2...1; 0/1...5 ; 0/2...10 V
±1, ±5 and ±10 V Direct or Inverted action |
V-curve function, 100-0-100% | 1-0-1, 5-0-5 and 10-0-10 V |
Load (@ voltage output) | ≥ 500 kΩ |
Response time, programmable | 0.0...60.0 s |
Output limitation - outside range: on unipolar V signals starting from 0 | 0 and 115% of max. value |
Output limitation - outside range: on unipolar V signals with offset | -5% of min. value and 115% of max. value |
Output limitation - outside range: on bipolar V signals | ±115% of min. & max. values |
Sensor error indication, at 4...20 mA input: selectable | Low, High, Zero, None |
Observed authority requirements
EMC | 2014/30/EU & UK SI 2016/1091 |
LVD | 2014/35/EU & UK SI 2016/1101 |
RoHS | 2011/65/EU & UK SI 2012/3032 |
EAC | TR-CU 020/2011 |
Approvals
c UL us, UL 508 | E248256 |
FM | 3025177 |
DNV Marine | TAA0000101 |
Need support to select the right product for your application?
Our sales engineers are ready to help specify the right device to meet your needs.
Reach out by phone to get in touch with us straight away – or use the contact form or quick quote function to send your RFQ directly from the website. You’ll get a response within 24 hours on normal business days.
You can expect to get a confirmed delivery date via email within 2 days after we have received your order.
As soon as your package leaves our warehouse, you’ll receive tracking details via email. And if you have any questions along the way we’re just a phone call or email away.
State-of-the-art manufacturing Our 8,500 sqm integrated and automated manufacturing campus in Denmark covers the entire value-chain from design and development to manufacturing. It allows us to design and optimize for testing and manufacturing thereby constantly driving quality up and costs down. |
Dedicated Presale / Aftersales
|
Product reliability |
Product deployment
|
Smart products
Check out our range of communication interfaces
|